Texecom premier odyssey 3e installation manual

[Helmi]

Texecom premier odyssey 3e installation manual
.
.
Download / Read Online Texecom premier odyssey 3e installation manual
.
.
.

.
High enough to be out of normal reach to deter tampering Safe ladder access Good cable access In addition to the corner screw fixing points, the unit also has a central keyhole to simplify mounting and aid levelling. Four screws and wall plugs are required for mounting the backplate to an even surface. An additional screw may be required to provide wall tamper by fitting through the screw hole next to the dual tamper microswitch. In doing so, care must be taken to leave the screw head slightly proud to ensure that the microswitch remains level and closes correctly when the outer cover is fitted. For maximum weatherproofing the unit should be flat to the wall. Test input for enabling remote test via Maintex or Wintex, or any supporting panel. Negative Removed on Tamper Input, and reports Tamper when there is a power loss to the sounder. When connecting the unit to the control panel, it is recommended that wiring should be connected to the unit first and the control panel second. The unit should then be initially powered from the control panel. LEDs will alternate slowly to signal normal operation. Off mode is immediately cancelled when the sounder is activated from the control panel. EN additional wiring is required at Grade 3 to monitor the status of the battery, the supply voltage and the integrity of the trigger wire. The two diagrams below show wiring configurations for Texecom control panels, and other manufacturers. Please check the Control Panel installation manual for any programming requirements relating to Grade 3 installations. Texecom Premier Elite Panel Other Control Panel Test Input The test input can be used to invoke a remote sounder test, this performs the same functions as the self test which is carried out once every 24 hours. To invoke the test the input must be placed at 0V for a minimum of 60s, during this time the Fault relay will open to signal the test is in progress. On completion of a successful test the Fault relay will close, if the test fails the relay will stay open. Off mode automatically cancels when both the tamper circuit is closed and power is supplied from the control panel. Prolonged battery first connection without power from the control panel may cause permanent damage to the internal battery. Texecom recommend that the unit is initially powered on battery only for no longer than 24 hours. Remove tamper wire from MSW 2 on first unit and connect to spare core. On second unit connect spare core into MSW 1. For Grade 3 installations using multiple units the Fault relays should be wired in series. If more than one unit is connected to an installation, the current demand may exceed the rated current output of the control panel. SCB mode on one or more of the connected units. SCB jumper is in the SAB position and move the LC jumper to the Low Current on position. Although volume is somewhat reduced, lowering the current demand on the control panel will enable the connection of additional sounder units. SCB jumper to the SCB position before the unit is connected to the control panel. When selecting SCB mode the battery must be connected before power is supplied from the control panel. If a unit is powered from a control panel with SCB mode selected but without the battery connected, the unit will not operate correctly due to the lack of power provided. Commissioning Most control panels have a method of testing the siren and strobe, which should be utilised for final testing. Failing this, simply arm the system and cause an alarm to confirm correct operation. Please note, it cannot be guaranteed that the battery is fully charged on installation. BEFORE OPENING THE COVER ALLOW AT LEAST 3 MINUTES AFTER THE LAST STROBE FLASH Most control panels have a method of testing the siren and strobe, which should be utilised. This is invoked by activating and deactivating the strobe three times within 30 seconds. Most control panels have a method of testing the strobe, which should be utilised. Off mode is shown to be active with the tamper circuit secure by the right LED only flashing. Once the outer cover is removed the left LED only will flash to indicate that the tamper circuit is open. If remote power is removed, and the tamper circuit is left closed, the right LED with flash rapidly to indicate that the unit is on standby battery power. Off will automatically start to cancel, indicated by the LEDs alternating rapidly for a further 2 minutes. Off mode is immediately cancelled when the sounder is activated from the control panel unless the system is powered down. Safety INSTALLATION AND MAINTENANCE BY QUALIFIED SERVICE PERSONNEL ONLY All strobes produce hazardous voltages. However, the unit includes dual circuit safety interlocks. NEVER remove the cover when the strobe is flashing WAIT 3 minutes after the strobe stops flashing before removing the cover AVOID touching the part of the PCB labelled Warning High Voltage The unit incorporates software which disables the strobe whilst the ta filexlib.
.
Texecom premier odyssey 3e installation manually
Texecom premier odyssey 3e installation kezikonyv
Texecom premier odyssey 3e installation manualidades
Texecom premier odyssey 3e installation manual
Texecom premier odyssey 3e installation كتيب

[投稿者]

投稿